-
Attaches Steel Bar Grating to Structural Shapes
Grating Clip model BCGC-516 is a galvanized carbon steel grating fastener used to fasten steel bar grating to structural shapes where the structural flange is in a horizontal plane. For appropriate use, the maximum measure from the top of the grating to the bottom of the flange is 2.5 inches. It can be used on 22-spaced grating and 30-spaced grating. It will work on 19-spaced grating, but note that the grating bars will spread during tightening. Model BCGC-516 consists of four parts, which are packed as 20 assembled units to a standard box. The principal part is the bottom portion of the assembly. This is a stamped and formed shape to contact the structure in the front and the grating in the rear. The second part is the curved top plate, which fits over the top of the grating surface. The body and top are joined by the third and fourth parts, a 5/16” diameter bolt and nut. MODEL BCGC-516 INFORMATION PAGE -
Attach Wide Spaced Bar Grating to Structural Shapes
G-Clip model FFGN is a galvanized carbon steel grating fastener used to fasten grating with wide spaced bars, typically 38-space. Like many of our other G-Clips, they are for use where the structural flange is in a horizontal plane. G-Clip model FFGN fastener consists of three parts, which are assembled at the factory into a complete installation unit, packed 25 units to a standard box. The principal part is the grip-jaw portion of the assembly, which has a female-thread form in its upper portion. This grip-jaw is die-stamped, with die-cut, toothed-shaped segments facing upward, which contact the underside of the structural member. The second part is the stamped top, which fits flat over the grating upper surface. The body and top are joined by the third part, a 1/4"-20 threaded bolt. This bolt varies in length to suit what is required for the application. VIEW FFGN PRODUCT INFORMATION SHEET VIEW FFGN PRODUCT ENGINEERING DETAIL
-
Attach T-Bar Fiberglass Grating to Structural Shapes.
G-Clip model FFSCGC is a 316-stainless steel grating fastener used to fasten fiberglass T-bars to structural members. Like many of our other G-Clips, they are for use where the structural flange is in a horizontal plane. Other stainless steel tops are available for use with the SCGC gripjaw, to be used on popular pultruded and molded fiberglass gratings with a minimum of 3/8” opening. G-Clip model FFSCGC- fastener consists of three parts, which are assembled at the factory into a complete installation unit, packed 25 units to a standard box. The principal part is the grip-jaw portion of the assembly, which has a female-thread form in its upper portion. This grip-jaw is casting, with toothed-shaped segment facing upward, which contact the underside of the structural member. The second part is the stamped top, which fits flat over the grating upper surface. The body and top are joined by the third part, a 1/4"-20 threaded bolt. This bolt varies in length to suit what is required for the application. MODEL FFSCGC INFORMATION PAGE -
Attach Odd-spaced Fiberglass Grating to structures.
G-Clip model FFSSGG- is a flattened, 316-stainless steel grating fastener used to fasten odd-spaced bar centers to structural shapes, where the structural flange is in a horizontal plane. Specially modified top assembly is designed to span a total of 3-1/16" with good rigidity and fits flat across the top of the grating surface. G-Clip model FFSSGG- fastener consists of three parts, which are assembled at the factory into a complete installation unit, packed 50 units to a standard box. The principal part is the body assembly, which has a female-thread form in its upper portion. Body lower portion is die-stamped, with die-cut, toothed shaped segments facing upward, which contact the underside of the structural member. The second part is the specially-shaped stamped top, further modified, which fits flat over the grating upper surface. The top is 3- overall width, designed to span many odd bars The body and top are joined by a 1/4"-20 threaded bolt, in proper length for the application. MODEL FFSSGG INFORMATION SHEET VIEW FFSSGG ENGINEERING DETAIL -
Attach Pultruded Fiberglass Grating to fiberglass structures.
G-Clip Model FSSGF is a 316-stainless steel grating fastener used to fasten pultruded bar grating to fiberglass or coated steel structural shapes, where the structural flange is in a horizontal plane. The specially shaped top is designed to fit pultruded grating shapes, while restricting the spreading of the bearing bars. G-Clip model FSSGF fastener consists of three parts, which are assembled at the factory into a complete installation unit, packed 25 units to a standard box. The principal part is the grip-jaw portion of the assembly, which has a female-thread form in its upper portion. This grip-jaw is die-stamped, with die-cut, flatted pads facing upward, which contact the underside of the structural member. The second part is the stamped top, which fits flat over the grating upper surface. It is specifically designed for pultruded grating shapes. The body and top are joined by the third part, a 1/4"-20 threaded bolt. This bolt varies in length to suit what is required for the application. MODEL FSSGF INFORMATION PAGE VIEW MODEL FSSGF ENGINEERING DETAILS -
Attach Pultruded Grating to Steel Structures
G-Clip Model FSSGG is a 316-stainless steel grating fastener used to fasten pultruded bar grating to metal or other structural shapes, where the structural flange is in a horizontal plane. The specially shaped top is designed to fit pultruded grating shapes, while restricting the spreading of the bearing bars. G-Clip model FSSGG fastener consists of three parts, which are assembled at the factory into a complete installation unit, packed 25 units to a standard box. The principal part is the grip-jaw portion of the assembly, which has a female-thread form in its upper portion. This grip-jaw is die-stamped, with die-cut, toothed-shaped segments facing upward, which contact the underside of the structural member. The second part is the stamped top, which fits flat over the grating upper surface. The body and top are joined by the third part, a 1/4"-20 threaded bolt. This bolt varies in length to suit what is required for the application. MODEL FSSGG INFORMATION PAGE VIEW FSSGG-CLIP PRODUCT ENGINEERING DETAIL -
Attach bar grating to flanges of angle shapes or channel shapes, where the flange of the shape is in a vertical plane.
Model GA- fastener consists of three parts, which are assembled at the factory into a complete installation unit, packed 50 pieces into a standard box. The principal part is the lower body assembly, a J-shaped assembly with a female thread, which hooks under the underside of (vertical) structural shape. The second part is the stamped top, which fits over the grating upper surface. The body and top are joined by a 1/4" - 20 threaded bolt, in proper length for the application. VIEW MODEL GA INFORMATION SHEET -
Attach Grating to steel structures.
Available in galvanized, steel, and aluminum.Fits 19 Space Gratings
Fastens grating to a horizontal-facing steel structural member edge.
The model GG- describes an assembly of fastener parts identical but for materials of construction, that each contain three common parts.
- First is a G-Clips unique top for better holding strength and to suit 19W4 grating.
- Second, a G-Clips patented bottom connects to the beam underside. A hex-headed cap screw connects the two, and its length suits the grating height being installed.
-
Model GG-0 "Short-Grip"
G-Clip Model GG-0 is a galvanized carbon steel grating fastener used to fasten 1” high 19-space bar grating to minimal-thickness structural member edges. The GG-0 will clamp 1” grating to beam edges as thin as 0.05”. In some cases, the GG-0 will also work for 0.75” tall gratings G-Clip model GG-0 fastener consists of three parts, which are assembled at the factory into a complete installation unit, packed 50 units to a standard box. The principal part is the grip-jaw portion of the assembly, which has a female-thread form in its upper portion. This grip-jaw is die-stamped, with die-cut, toothed-shaped segments facing upward, which contact the underside of the structural member. The second part is the stamped top, which fits flat over the grating upper surface. The body and top are joined by the third part, a 1/4"-20 threaded bolt. This bolt varies in length to suit what is required for the application. MODEL GG-0 INFORMATION SHEET MODEL GG-0 ENGINEERING DETAIL -
Attach 19-space Bar Grating to Structural Surfaces Ranging in Thickness from .75” up to 1.25” thick.
G-Clip model GG-2 is a galvanized carbon steel grating fastener used to fasten 19-space bar grating to structural member edges ranging in thickness from .75” up to 1.25” thick. G-Clip model GG-2 fastener consists of three parts, which are assembled at our Louisiana factory into a complete installation unit, packed 50 units to a standard box. The principal part is the grip-jaw portion of the assembly, which has a female-thread form in its upper portion. This grip-jaw is die-stamped, with die-cut, toothed-shaped segments facing upward, which contact the underside of the structural member. The second part is the stamped top, which fits flat over the grating upper surface. The body and top are joined by the third part, a 1/4"-20 threaded bolt. This bolt varies in length to suit what is required for the application. VIEW GG-2 PRODUCT INFORMATION SHEET VIEW GG-2 PRODUCT ENGINEERING DETAIL -
Model GN-1 "Narrow-Grip"
Attach 15-space grating to structures with horizontal edges.G-Clip model GN-1 is a galvanized carbon steel grating fastener used to fasten 15-space bar grating to structural shapes, where the structural flange is in a horizontal plane. This unit has a narrower width than our GG-1 series.
GN-1 "Narrow Grip" INFORMATION SHEET VIEW GN-1 PRODUCT ENGINEERING DETAIL -
Attaches Galvanized Steel Grating to Structural Shapes
Grating Clip model GSLF-38 is a galvanized steel grating fastener used to fasten standard steel bar grating to structural shapes where the structural flange is in a horizontal plane. For appropriate use, the maximum measure from the top of the grating to the bottom of the beam flange should be 2” or less. It is designed to be used on 19-spaced grating with bearing bars from 1/8” to 1/4" wide. Model GSLF-38consists of 3 parts, which are packed as 20 assembled units to a standard box. The principal part is the bottom portion of the assembly. This is a steel casting with the defining feature being the “stair-step” on the back end. The second part is the curved top plate, which fits flat over the grating upper surface. This part is commonly called a “saddle clip.” The body and top are joined by the third part, a 3/8”diameter threaded socket-head bolt. This bolt is fully threaded over a 2-1/4” length. The body and top are joined by the third and fourth parts, a 5/16” diameter bolt and nut. MODEL GSLF-38 INFORMATION PAGE -
Attach Odd Shaped Bar Grating to Structural Shapes Where the Flange is in a Horizontal Plane
G-Clip model RGN is a galvanized carbon steel grating fastener used to fasten odd-spaced gratings to structural members, where the flange is in a horizontal plane. G-Clip model RGN fastener consists of three parts, which are assembled at our Louisiana factory into a complete installation unit, packed 50 units to a standard box. The principal part is the grip-jaw portion of the assembly, which has a female-thread form in its upper portion. This grip-jaw is die-stamped, with die-cut, toothed-shaped segments facing upward, which contact the underside of the structural member. The second part is the stamped top, which fits flat over the grating upper surface. The body and top are joined by the third part, a 1/4"-20 threaded bolt. This bolt varies in length to suit what is required for the application. VIEW MODEL RGN INFORMATION SHEET VIEW MODEL RGN ENGINEERING DETAIL
-
Attach Close Mesh Grating to Structural Shapes
MODEL RSCGC is a 316-stainless steel grating fastener used to fasten close mesh bar grating to metal or other structural shapes, where the structural flange is in a horizontal plane. The narrow grip-jaw on the clip allows it to be used on gratings with as little as 3/8” opening. Our nickname for this part is “Cast Close-Grip.” G-Clip model RSCGC fastener consists of three parts, which are assembled at our factory in Louisiana, then packed 50 units to a box. The principal part is the grip-jaw portion of the assembly. This grip-jaw is cast stainless steel, with toothed-shaped segments facing upward. The second part is the stamped top, which fits flat over the grating upper surface. The round shape allows it to be used on almost any bearing bar configuration. The body and top are joined by the third part, a 1/4"-20 threaded bolt. This bolt varies in length to suit the application, always 1/4” shorter than the height of the grating. MODEL RSCGC INFORMATION PAGE
