-
Attach Odd-spaced Fiberglass Grating to structures.
G-Clip model FFSSGG- is a flattened, 316-stainless steel grating fastener used to fasten odd-spaced bar centers to structural shapes, where the structural flange is in a horizontal plane. Specially modified top assembly is designed to span a total of 3-1/16" with good rigidity and fits flat across the top of the grating surface. G-Clip model FFSSGG- fastener consists of three parts, which are assembled at the factory into a complete installation unit, packed 50 units to a standard box. The principal part is the body assembly, which has a female-thread form in its upper portion. Body lower portion is die-stamped, with die-cut, toothed shaped segments facing upward, which contact the underside of the structural member. The second part is the specially-shaped stamped top, further modified, which fits flat over the grating upper surface. The top is 3- overall width, designed to span many odd bars The body and top are joined by a 1/4"-20 threaded bolt, in proper length for the application. MODEL FFSSGG INFORMATION SHEET VIEW FFSSGG ENGINEERING DETAIL -
Attach devices to grating surface
Model GP-1 Available in Galvanized Carbon Steel. Model SSGP-1 Available in 316-Stainless Steel. The model GP-1 describes an assembly of fastener parts that can be used to fasten parallel grating panels to each other. The top part is a G-Clips unique top for better holding strength and to suit 19W4 grating. Second, a G-Clips patented bottom bar connects between the grating panel underside and projects sideways under the second grating panel. A hex-headed cap screw connects the two, and its length suits the grating height being installed Use of this model can reduce the deflection that often occurs when a single grating panel deflects downward due to traffic, and adjacent but unconnected panels cause an inadvertent trip hazard. By combining the strength of two panels, the load is shared, and deflection is lessened. Used properly, this can reduce trip hazards. VIEW MODEL GP INFORMATION SHEET -
316 Stainless Steel top fits into 2" square-mesh fiberglass
Grating Fasteners designs include a number of different tops that are assembled with the patented G-Clips bottom, ready-to-install and sized to fit many grating sizes. G-Clips tops are available in quantities as separate units and provide more hold-down strength than typical saddle clips. Used with a self-drilling screw, G-Clips tops provide a superior method of attaching grating when compared to saddle clips. GT MODEL (TOP ONLY) PRODUCT INFORMATION SHEET -
316 Stainless Steel top is designed to fit 1-1/2" square-mesh fiberglass grating
Grating Fasteners designs include a number of different tops that are assembled with the patented G-Clips bottom, ready-to-install and sized to fit many grating sizes. G-Clips tops are available in quantities as separate units and provide more hold-down strength than typical saddle clips. Used with a self-drilling screw, G-Clips tops provide a superior method of attaching grating when compared to saddle clips. GT MODEL (TOP ONLY) PRODUCT INFORMATION SHEET -
316 Stainless Steel top fits into either a 3/4" or 1" wide slot of any grating
Grating Fasteners designs include a number of different tops that are assembled with the patented G-Clips bottom, ready-to-install and sized to fit many grating sizes. G-Clips tops are available in quantities as separate units and provide more hold-down strength than typical saddle clips. Used with a self-drilling screw, G-Clips tops provide a superior method of attaching grating when compared to saddle clips. GT MODEL (TOP ONLY) PRODUCT INFORMATION SHEET -
316 Stainless Steel top fits specialty gratings on 2-3/8" bar spacing, and other wide-spaced gratings
Grating Fasteners designs include a number of different tops that are assembled with the patented G-Clips bottom, ready-to-install and sized to fit many grating sizes. G-Clips tops are available in quantities as separate units and provide more hold-down strength than typical saddle clips. Used with a self-drilling screw, G-Clips tops provide a superior method of attaching grating when compared to saddle clips. GT MODEL (TOP ONLY) PRODUCT INFORMATION SHEET -
316 stainless steel top is made to fit pultruded fiberglass gratings
Grating Fasteners designs include a number of different tops that are assembled with the patented G-Clips bottom, ready-to-install and sized to fit many grating sizes. G-Clips tops are available in quantities as separate units and provide more hold-down strength than typical saddle clips. Used with a self-drilling screw, G-Clips tops provide a superior method of attaching grating when compared to saddle clips. GT MODEL (TOP ONLY) PRODUCT INFORMATION SHEET -
Attach 2" Square Mesh Fiberglass Grating to structural shapes.
G-Clip model ZSSGG is a 316-stainless steel grating fastener used to fasten 2" square mesh fiberglass grating to structural shapes where the structural flange is in a horizontal plane. Specially shaped top assembly is designed to fit 2" square mesh. The principal part is the body assembly, which has a female thread form in its upper portion. Body lower portion is die-stamped, with die-cut, toothed shape segments facing upward, which contact the underside of the structural member. The second part is the specially-shaped, stamped top, which fits into the grating upper surface and presses downward around the tops of the square. The body and top are joined by a 1/4" -20 threaded bolt, in proper length for the application. 316 Stainless Steel MODEL ZSSGG INFORMATION PAGE VIEW ZSSGG-CLIP PRODUCT ENGINEERING DETAIL -
Attach 1" x 4" Molded Fiberglass or Bar Grating to Metal or Other Structural Shapes
Model XSSGG: G-Clips unique top for better holding strength and to suit 19W4 grating. Second, a G-Clips patented bottom connects to the beam underside. A hex-headed cap screw connects the two, and its length suits the grating height being installed. G-Clip model XSSGG is a 316-stainless steel grating fastener used to fasten bar grating to metal or other structural shapes, where the structural flange is in a horizontal plane. The model "X" top is a rectangular-shaped top, and can fit a 3/4" wide slot between two bearing bars. Turned 90 degrees, it can fit a 1" slot. G-Clip model XSSGG- fastener consists of three parts, which are assembled at the factory into a complete installation unit, packed 50 units to a standard box. The principal part is the body assembly, which has a female thread form in its upper portion. Body lower portion is die-stamped, with die-cut, toothed shape segments facing upward, which contact the underside of the structural member. The second part is the rectangular-shaped, stamped top, which fits into the grating upper surface. The body and top are joined by a 1/4" -20 threaded bolt, in proper length for the application. MODEL XSSGG INFORMATION PAGE VIEW XSSGG-CLIP PRODUCT ENGINEERING DETAIL -
Attach Pultruded Grating to Steel Structures
G-Clip Model FSSGG is a 316-stainless steel grating fastener used to fasten pultruded bar grating to metal or other structural shapes, where the structural flange is in a horizontal plane. The specially shaped top is designed to fit pultruded grating shapes, while restricting the spreading of the bearing bars. G-Clip model FSSGG fastener consists of three parts, which are assembled at the factory into a complete installation unit, packed 25 units to a standard box. The principal part is the grip-jaw portion of the assembly, which has a female-thread form in its upper portion. This grip-jaw is die-stamped, with die-cut, toothed-shaped segments facing upward, which contact the underside of the structural member. The second part is the stamped top, which fits flat over the grating upper surface. The body and top are joined by the third part, a 1/4"-20 threaded bolt. This bolt varies in length to suit what is required for the application. MODEL FSSGG INFORMATION PAGE VIEW FSSGG-CLIP PRODUCT ENGINEERING DETAIL -
Model GN-1 "Narrow-Grip"
Attach 15-space grating to structures with horizontal edges.G-Clip model GN-1 is a galvanized carbon steel grating fastener used to fasten 15-space bar grating to structural shapes, where the structural flange is in a horizontal plane. This unit has a narrower width than our GG-1 series.
GN-1 "Narrow Grip" INFORMATION SHEET VIEW GN-1 PRODUCT ENGINEERING DETAIL -
Saddle clips are used to attach grating to structural members.
A popular method of attaching grating to structures involves formed metal pieces, variously called saddle clips, butterfly clips, and M-Clips, placed onto the grating top surface and attached with a suitable screw, bolt, or pin to the structure. All of our saddle clips are designed for use with a 0.25” diameter fastener.
Saddle Clips offered by our company include the following units:
SSI-60-1: This saddle clip is designed for use on fiberglass, pultruded gratings that are 1” in height. Like the SSF-10, it is resistant to corrosion, due to its stainless steel material. SSI-60-1.5: This saddle clip is designed for fiberglass, pultruded gratings that are 1.5” in height or more. It can also be used on 1.5” square mesh fiberglass gratings. It is also made of stainless steel.
-
Attach Pultruded Fiberglass Grating to fiberglass structures.
G-Clip Model FSSGF is a 316-stainless steel grating fastener used to fasten pultruded bar grating to fiberglass or coated steel structural shapes, where the structural flange is in a horizontal plane. The specially shaped top is designed to fit pultruded grating shapes, while restricting the spreading of the bearing bars. G-Clip model FSSGF fastener consists of three parts, which are assembled at the factory into a complete installation unit, packed 25 units to a standard box. The principal part is the grip-jaw portion of the assembly, which has a female-thread form in its upper portion. This grip-jaw is die-stamped, with die-cut, flatted pads facing upward, which contact the underside of the structural member. The second part is the stamped top, which fits flat over the grating upper surface. It is specifically designed for pultruded grating shapes. The body and top are joined by the third part, a 1/4"-20 threaded bolt. This bolt varies in length to suit what is required for the application. MODEL FSSGF INFORMATION PAGE VIEW MODEL FSSGF ENGINEERING DETAILS -
Model GG-0 "Short-Grip"
G-Clip Model GG-0 is a galvanized carbon steel grating fastener used to fasten 1” high 19-space bar grating to minimal-thickness structural member edges. The GG-0 will clamp 1” grating to beam edges as thin as 0.05”. In some cases, the GG-0 will also work for 0.75” tall gratings G-Clip model GG-0 fastener consists of three parts, which are assembled at the factory into a complete installation unit, packed 50 units to a standard box. The principal part is the grip-jaw portion of the assembly, which has a female-thread form in its upper portion. This grip-jaw is die-stamped, with die-cut, toothed-shaped segments facing upward, which contact the underside of the structural member. The second part is the stamped top, which fits flat over the grating upper surface. The body and top are joined by the third part, a 1/4"-20 threaded bolt. This bolt varies in length to suit what is required for the application. MODEL GG-0 INFORMATION SHEET MODEL GG-0 ENGINEERING DETAIL
