Shop

  • Saddle clips are used to fasten 15 spaced steel bar grating to structural members.

    Grating Fasteners Model GSCF-7 is a galvanized steel grating fastener used to fasten 15 spaced steel bar grating to structural shapes. This particular fastener can be installed with a tek screw. The GSCF-7 saddle clip, is an M-shaped, stamped and formed piece of 14 gauge steel, galvanized, that fits over the grating upper surface. A hole is punched in the center of the clip to allow a 1/4” tek screw or other fastener to be used. Tek screws are not included with the saddle clips, but can be purchased separately. A zinc plated or 410 SS #14 screw is available. The screw has a 3/8” hex washer head. The point in the tek screw is a #3 point. This screw is available in two sizes, 1-1/2” or 2. (Other sizes can be requested) SADDLE CLIP INFORMATION PAGE SADDLE CLIP GSCF-7 INFORMATION PAGE  
  • Saddle clips are used to attach grating to structural members.

    SSGF-1.5  Saddle Clip: Available 316-series stainless steel Saddle clips are used to attach 1-1/2” square mesh fiberglass grating to structural shapes. Grating Fasteners Model SSGF-1.5 is a 316 stainless steel grating fastener used to fasten 1-1/2” square mesh fiberglass grating to structural shapes. This particular fastener can be installed with a tek screw. The SSGF-1.5 saddle clip, is an M-shaped, stamped and formed piece of 16 gauge 316 stainless steel that fits over the grating upper surface. A hole is punched in the center of the clip to allow a 1/4” tek screw or other fastener to be used. Tek screws are not included with the saddle clips, but can be purchased separately. A 410 SS #14 screw is available. The screw has a 3/8” hex washer head. The point in the tek screw is a #3 point. This screw is available in two sizes, 1-1/2” or 2. (Other sizes can be requested) SADDLE CLIP INFORMATION PAGE SADDLE CLIP SSGF-1.5 INFORMATION PAGE  
  • Attach Lightweight Devices to a Structural Surfaces thick.

    G-Clip Model GM is a fastener used to fasten lightweight devices to 19-space bar grating. The GM-1/2” is designed to be used instead of J-bolts. It will withstand 1000 pounds of direct upward pull force. G-Clip Model GM fastener consists of three parts, which are assembled at the factory into a complete installation unit, packed 20 units to a standard box. The principal part is the lower body of the assembly, which is a specially stamped wing that is mechanically galvanized and holds captive a ½” zinc-plated nut. This lower body contacts the underside of the grating panel. The second part is the stamped top, which fits flat over the grating upper surface. The top is 2” wide and has an octagon shape. This plate is mechanically galvanized. The body and top are joined by the third part, a 1/2:” zinc-plated threaded stud. This stud is either 3” or 5” in length, depending on the job required. The body and top are joined by the third part, a 1/4"-20 threaded bolt. This bolt varies in length to suit what is required for the application. VIEW GM PRODUCT ENGINEERING DETAIL
  • Attach 19-space Bar Grating to Structural Surfaces Ranging in Thickness from .75” up to 1.25” thick.

    G-Clip model GG-2 is a galvanized carbon steel grating fastener used to fasten 19-space bar grating to structural member edges ranging in thickness from .75” up to 1.25” thick. G-Clip model GG-2 fastener consists of three parts, which are assembled at our Louisiana factory into a complete installation unit, packed 50 units to a standard box. The principal part is the grip-jaw portion of the assembly, which has a female-thread form in its upper portion. This grip-jaw is die-stamped, with die-cut, toothed-shaped segments facing upward, which contact the underside of the structural member. The second part is the stamped top, which fits flat over the grating upper surface. The body and top are joined by the third part, a 1/4"-20 threaded bolt. This bolt varies in length to suit what is required for the application. VIEW GG-2 PRODUCT INFORMATION SHEET VIEW GG-2 PRODUCT ENGINEERING DETAIL
  • Attach Wide Spaced Bar Grating to Structural Shapes

    G-Clip model FFGN is a galvanized carbon steel grating fastener used to fasten grating with wide spaced bars, typically 38-space. Like many of our other G-Clips, they are for use where the structural flange is in a horizontal plane. G-Clip model FFGN fastener consists of three parts, which are assembled at the factory into a complete installation unit, packed 25 units to a standard box. The principal part is the grip-jaw portion of the assembly, which has a female-thread form in its upper portion. This grip-jaw is die-stamped, with die-cut, toothed-shaped segments facing upward, which contact the underside of the structural member. The second part is the stamped top, which fits flat over the grating upper surface. The body and top are joined by the third part, a 1/4"-20 threaded bolt. This bolt varies in length to suit what is required for the application. VIEW FFGN PRODUCT INFORMATION SHEET VIEW FFGN PRODUCT ENGINEERING DETAIL Size Chart Model FFGN
  • Attach Odd Shaped Bar Grating to Structural Shapes Where the Flange is in a Horizontal Plane

    G-Clip model RGN is a galvanized carbon steel grating fastener used to fasten odd-spaced gratings to structural members, where the flange is in a horizontal plane. G-Clip model RGN fastener consists of three parts, which are assembled at our Louisiana factory into a complete installation unit, packed 50 units to a standard box. The principal part is the grip-jaw portion of the assembly, which has a female-thread form in its upper portion. This grip-jaw is die-stamped, with die-cut, toothed-shaped segments facing upward, which contact the underside of the structural member. The second part is the stamped top, which fits flat over the grating upper surface. The body and top are joined by the third part, a 1/4"-20 threaded bolt. This bolt varies in length to suit what is required for the application. VIEW MODEL RGN INFORMATION SHEET VIEW MODEL RGN ENGINEERING DETAIL Size Chart Model RGN
  • Attach Odd Shaped Bar Grating to Structural Shapes

    G-Clip model RSSGG is a 316-stainless steel grating fastener used to fasten odd-shaped bar grating to metal or other structural shapes, where the structural flange is in a horizontal plane. Other stainless steel tops are available for use with the SSGG grip-jaw, to be used on popular pultruded and molded fiberglass gratings, or in highly corrosive environments. G-Clip model RSSGG fastener consists of three parts, which are assembled at the factory into a complete installation unit, packed 50 units to a standard box. The principal part is the grip-jaw portion of the assembly, which has a female-thread form in its upper portion. This grip-jaw is die-stamped, with die-cut, toothed-shaped segments facing upward, which contact the underside of the structural member. The second part is the stamped top, which fits flat over the grating upper surface. The body and top are joined by the third part, a 1/4"-20 threaded bolt. This bolt varies in length to suit what is required for the application. VIEW RSSGG PRODUCT INFORMATION SHEET VIEW RSSGG PRODUCT ENGINEERING DETAIL Size Chart Model RSSGG
  • Attach Close Mesh Grating to Structural Shapes

    MODEL RSCGC is a 316-stainless steel grating fastener used to fasten close mesh bar grating to metal or other structural shapes, where the structural flange is in a horizontal plane. The narrow grip-jaw on the clip allows it to be used on gratings with as little as 3/8” opening. Our nickname for this part is “Cast Close-Grip.” G-Clip model RSCGC fastener consists of three parts, which are assembled at our factory in Louisiana, then packed 50 units to a box. The principal part is the grip-jaw portion of the assembly. This grip-jaw is cast stainless steel, with toothed-shaped segments facing upward. The second part is the stamped top, which fits flat over the grating upper surface. The round shape allows it to be used on almost any bearing bar configuration. The body and top are joined by the third part, a 1/4"-20 threaded bolt. This bolt varies in length to suit the application, always 1/4” shorter than the height of the grating. MODEL RSCGC INFORMATION PAGE
  • Attach T-Bar Grating to Parallel Grating Panels.

    MODEL SSGP is a stainless steel fastener used to fasten parallel sheets of bar grating together. The purpose of the SSGP- is to prevent deflection due to weight loads and eliminate trip hazards. It requires a companion model SSGG- to be installed correctly. They are sold either alone as SSGP’s or in SSGP/SSGG sets. G-Clip model SSGP fastener consists of three parts, which are assembled at the factory into a complete installation unit, packed 25 to a standard box. The principal part is the lower body of the assembly, which has a female-thread form. The lower body portion of the clip is a die-stamped piece of galvanized flat bar. This flat bar creates a flange for the SSGG grip jaw. The lower body contacts the underside of both grating panels. The second part is the stamped top, which fits flat on the grating top surface. The body and top are joined by the third part, a 1/4”- 20 316SS threaded bolt. This bolt varies in length, depending on the depth of the grating. MODEL SSGP INFORMATION PAGE
  • Attach Lightweight Devices to 19 Space Bar Grating.

    Grating Clip model SSGM is a stainless steel fastener used to fasten lightweight devices to 19-space bar grating. The SSGM-1/2” is designed to be used instead of J-bolts. It will withstand 1000 pounds of direct upward pull force. Due to its 316SS material, it can be used in corrosive environments. Model SSGM fastener consists of three parts, which are assembled at the factory into a complete installation unit, packed 20 units to a standard box. The principal part is the lower body of the assembly, which is a specially stamped wing that holds captive a ½” 316SS nut. This lower body contacts the underside of the grating panel. The second part is the stamped top, which fits flat over the grating upper surface. The top is 2” wide and has an octagon shape. The body and top are joined by the third part, a 1/2” B8M threaded stud. This stud is either 3” or 5” in length, depending on the job required. MODEL SSMG INFORMATION PAGE  
  • Attaches Galvanized Steel Grating to Structural Shapes

    Grating Clip model GSLF-38 is a galvanized steel grating fastener used to fasten standard steel bar grating to structural shapes where the structural flange is in a horizontal plane. For appropriate use, the maximum measure from the top of the grating to the bottom of the beam flange should be 2” or less. It is designed to be used on 19-spaced grating with bearing bars from 1/8” to 1/4" wide. Model GSLF-38consists of 3 parts, which are packed as 20 assembled units to a standard box. The principal part is the bottom portion of the assembly. This is a steel casting with the defining feature being the “stair-step” on the back end. The second part is the curved top plate, which fits flat over the grating upper surface. This part is commonly called a “saddle clip.” The body and top are joined by the third part, a 3/8”diameter threaded socket-head bolt. This bolt is fully threaded over a 2-1/4” length. The body and top are joined by the third and fourth parts, a 5/16” diameter bolt and nut. MODEL GSLF-38 INFORMATION PAGE  
  • Attaches Steel Bar Grating to Structural Shapes

    Grating Clip model BCGC-516 is a galvanized carbon steel grating fastener used to fasten steel bar grating to structural shapes where the structural flange is in a horizontal plane. For appropriate use, the maximum measure from the top of the grating to the bottom of the flange is 2.5 inches. It can be used on 22-spaced grating and 30-spaced grating. It will work on 19-spaced grating, but note that the grating bars will spread during tightening. Model BCGC-516 consists of four parts, which are packed as 20 assembled units to a standard box. The principal part is the bottom portion of the assembly. This is a stamped and formed shape to contact the structure in the front and the grating in the rear. The second part is the curved top plate, which fits over the top of the grating surface. The body and top are joined by the third and fourth parts, a 5/16” diameter bolt and nut. MODEL BCGC-516 INFORMATION PAGE  
  • Attach T-Bar Fiberglass Grating to Structural Shapes.

    G-Clip model FFSCGC  is a 316-stainless steel grating fastener used to fasten fiberglass T-bars to structural members. Like many of our other G-Clips, they are for use where the structural flange is in a horizontal plane. Other stainless steel tops are available for use with the SCGC gripjaw, to be used on popular pultruded and molded fiberglass gratings with a minimum of 3/8” opening. G-Clip model FFSCGC- fastener consists of three parts, which are assembled at the factory into a complete installation unit, packed 25 units to a standard box. The principal part is the grip-jaw portion of the assembly, which has a female-thread form in its upper portion. This grip-jaw is casting, with toothed-shaped segment facing upward, which contact the underside of the structural member. The second part is the stamped top, which fits flat over the grating upper surface. The body and top are joined by the third part, a 1/4"-20 threaded bolt. This bolt varies in length to suit what is required for the application. MODEL FFSCGC INFORMATION PAGE  
  • Attach T-Bar Fiberglass Grating to Structural Shapes.

    G-Clip model ALGG is an aluminum grating fastener used to fasten 19-space bar grating to structural shapes, where the structural flange is in a horizontal plane. G-Clip model ALGG fastener consists of three parts, which are assembled at the factory into a complete installation unit, packed 50 units to a standard box. The principal part is the grip-jaw portion of the assembly, which has a female-thread form in its upper portion. This grip-jaw is die-stamped, with die-cut, toothed-shaped segments facing upward, which contact the underside of the structural member. The second part is the stamped top, which fits flat over the grating upper surface. The body and top are joined by the third part, a 1/4"-20 threaded bolt. This bolt varies in length to suit what is required for the application. MODEL ALGG INFORMATION PAGE VIEW MODEL ALGG ENGINEERING DETAILS  
  • Attach 1-1/2" Square Mesh Fiberglass Grating to structural shapes.

    G-Clip model YSSGG is a 316-stainless steel grating fastener used to fasten 1-1/2" square mesh fiberglass grating to structural shapes where the structural flange is in a horizontal plane. Specially shaped top assembly is designed to fit 1-1/2" square mesh. G-Clip model YSSGG- fastener consists of three parts, which are assembled at the factory into a complete installation unit, packed 50 units to a standard box. The principal part is the body assembly, which has a female thread form in its upper portion. Body lower portion is die-stamped, with die-cut, toothed shape segments facing upward, which contact the underside of the structural member. The second part is the specially-shaped, stamped top, which fits into the grating upper surface and presses downward around the tops of the square. The body and top are joined by a 1/4" -20 threaded bolt, in proper length for the application. MODEL YSSGG INFORMATION PAGE VIEW YSSGG PRODUCT ENGINEERING DETAIL  

Title

Go to Top