Engineered G-Clips

  • Attach bar grating to flanges of angle shapes or channel shapes, where the flange of the shape is in a vertical plane.
    Model GA- fastener consists of three parts, which are assembled at the factory into a complete installation unit, packed 50 pieces into a standard box. The principal part is the lower body assembly, a J-shaped assembly with a female thread, which hooks under the underside of (vertical) structural shape. The second part is the stamped top, which fits over the grating upper surface. The body and top are joined by a 1/4" - 20 threaded bolt, in proper length for the application. VIEW MODEL GA INFORMATION SHEET
  • Attach Lightweight Devices to a Structural Surfaces thick.

    G-Clip Model GM is a fastener used to fasten lightweight devices to 19-space bar grating. The GM-1/2” is designed to be used instead of J-bolts. It will withstand 1000 pounds of direct upward pull force. G-Clip Model GM fastener consists of three parts, which are assembled at the factory into a complete installation unit, packed 20 units to a standard box. The principal part is the lower body of the assembly, which is a specially stamped wing that is mechanically galvanized and holds captive a ½” zinc-plated nut. This lower body contacts the underside of the grating panel. The second part is the stamped top, which fits flat over the grating upper surface. The top is 2” wide and has an octagon shape. This plate is mechanically galvanized. The body and top are joined by the third part, a 1/2:” zinc-plated threaded stud. This stud is either 3” or 5” in length, depending on the job required. The body and top are joined by the third part, a 1/4"-20 threaded bolt. This bolt varies in length to suit what is required for the application. VIEW GM PRODUCT ENGINEERING DETAIL
  • Attach devices to grating surface

    Model GP-1 Available in Galvanized Carbon Steel. Model SSGP-1 Available in 316-Stainless Steel. The model GP-1 describes an assembly of fastener parts that can be used to fasten parallel grating panels to each other. The top part is a G-Clips unique top for better holding strength and to suit 19W4 grating. Second, a G-Clips patented bottom bar connects between the grating panel underside and projects sideways under the second grating panel. A hex-headed cap screw connects the two, and its length suits the grating height being installed Use of this model can reduce the deflection that often occurs when a single grating panel deflects downward due to traffic, and adjacent but unconnected panels cause an inadvertent trip hazard. By combining the strength of two panels, the load is shared, and deflection is lessened. Used properly, this can reduce trip hazards. VIEW MODEL GP INFORMATION SHEET
  • Attach Lightweight Devices to 19 Space Bar Grating.

    Grating Clip model SSGM is a stainless steel fastener used to fasten lightweight devices to 19-space bar grating. The SSGM-1/2” is designed to be used instead of J-bolts. It will withstand 1000 pounds of direct upward pull force. Due to its 316SS material, it can be used in corrosive environments. Model SSGM fastener consists of three parts, which are assembled at the factory into a complete installation unit, packed 20 units to a standard box. The principal part is the lower body of the assembly, which is a specially stamped wing that holds captive a ½” 316SS nut. This lower body contacts the underside of the grating panel. The second part is the stamped top, which fits flat over the grating upper surface. The top is 2” wide and has an octagon shape. The body and top are joined by the third part, a 1/2” B8M threaded stud. This stud is either 3” or 5” in length, depending on the job required. MODEL SSMG INFORMATION PAGE  
  • Attach T-Bar Grating to Parallel Grating Panels.

    MODEL SSGP is a stainless steel fastener used to fasten parallel sheets of bar grating together. The purpose of the SSGP- is to prevent deflection due to weight loads and eliminate trip hazards. It requires a companion model SSGG- to be installed correctly. They are sold either alone as SSGP’s or in SSGP/SSGG sets. G-Clip model SSGP fastener consists of three parts, which are assembled at the factory into a complete installation unit, packed 25 to a standard box. The principal part is the lower body of the assembly, which has a female-thread form. The lower body portion of the clip is a die-stamped piece of galvanized flat bar. This flat bar creates a flange for the SSGG grip jaw. The lower body contacts the underside of both grating panels. The second part is the stamped top, which fits flat on the grating top surface. The body and top are joined by the third part, a 1/4”- 20 316SS threaded bolt. This bolt varies in length, depending on the depth of the grating. MODEL SSGP INFORMATION PAGE

Title

Go to Top